CONTACT

The Esquadrias Galon , in order to offer its customers the best products and preserve its quality , guides so that they are observed the instructions below :

.1 - The environment must be clean and dry with maximum temperature in 30 C; 1.2 - Avoid the action of sun and rain on the product without prior waterproofs them ; 1.3 - The product should be supported on platforms and in horizontal position; 1.4 - Avoid that the product is exposed to moisture or materials that can stain them . Such as grease, cement, lime , oil , sand , and others. 1.5 - Do not put anything on the product beyond the protective material - plywood or similar , to not damage them ;

2.1 - Avoid warping and cracking waterproofing product in all the parties , immediately after removing from the package ; 2.2 - Before the first coat sand across the frame with sandpaper number 220, respecting the grain of the wood. Amounts are to be screwed in Vertical and horizontal crosspieces ; 2.3 - As a primer on the base of the timber , it is important to use sealer or dyer , for the closing of the pores ; 2.4 - not the application of lacquer and paints to water-based is recommended; 2.5 - The paint must be done by a qualified professional in order to preserve the quality and finish of the product; 2.6 - the renewal of painting every 2 years for the area is recommended internal and every 1 year for external area - to those exposed to the actions of weather ( sun and rain) ;

3.1 - Transportation must be done in a closed car ( trunk or lonado ) , and supported on platforms ; 3.2 - Be careful with the edges of the doors in handling non -breaking them ; 3.3 - The frames must be firmly fixed in the car, so that do not slip during the route and damage - ;

4.1 - Before fully fix the frame , check the level , square and bob; 4.2 - Check that the stop size match the measure of the gate ; 4.3 - Monte stop with screws and use two wooden rulers to stay in the square, see Figure 1; 4.4 - In chumbe masonry three clubs in each side and one above , these clubs should measure : 10x20x3,5 cm , serve the same to screw stop , see Figure 2; < Hr> 4.5 - between the putter and stop use shim in the exact thickness , do not use wedges because the screw should penetrate the bat at least two centimeters depth ; 4.6 - Make the special finishing with buttons in wood or mass to wood thus hiding the screw head ; 4.7 - The guamições should be cut in miter for perfect fitting on top; 4.8 - Add the cut pieces and stick them up on the anvil , use nails without head.

5.1 - Follow the items 4.1 and 4.2 ; 5.2 - Put the stopper in place. use wedges to steady him , attention to do not use too much pressure as this may cause warpage ; 5.3 - The foam application points should have an approximate space 80 cm linear stop as shown in figure 3 ; 5.4 - Try to observe the foam use guidelines with the manufacturer of the same; 5.5 - To install the garrisons follow the guidelines of the items 4.7 and 4.8 .

6.1 - Check the door measures and if there is warping before starting any installation procedure; 6.2 - The door should read clearance for expansion between the stop aproximadamenle 3 mm per side; 6.3 - Care for doors with cushions in diagonal, use the low part the hinge side check to clarify the figure 4; 6.4 - Install at least three hinges, because massive doors need good structure to hold it; 6.5 - The lock may have the maximum engine box 10.3 cm dista addition can affect the structure of the door; 6.6 - not affect the door structure changing its standard measures; 6.7 - For installation we recommend to hiring a professional specialized in the segment, it is fundamental one hand labor correct for the perfect working order.

---

Attention: The outer door can not directly receive rain and sun, protejaa with awning or shelter when the building there is no area will front door or something similar, wood as a natural product perceives climate change, so it is best to keep it protected the aggressive actions of the time. Failure to observe the information in this manual, will involve as a loss in the functioning of the product and consequently your warranty. wedge shim thin thick shim bat